Research on noise reduction of drive axle hypoid gear based on tooth surface mismatch modification

In order to reduce the transmission noise of drive axle hypoid gear, a method of tooth surface mismatch modification was proposed. Firstly, on the basis of establishing the grinding mathematical model of hypoid gear with cutter tilt, the theoretical tooth surface equation was derived, and the numeri...

وصف كامل

التفاصيل البيبلوغرافية
الحاوية / القاعدة:	Advances in Mechanical Engineering
المؤلفون الرئيسيون:	Shaowu Nie, Jinyu Chen, Shaohang Liu
التنسيق:	مقال
اللغة:	الإنجليزية
منشور في:	SAGE Publishing 2024-02-01
الوصول للمادة أونلاين:	https://doi.org/10.1177/16878132241228195

مواد مشابهة

Study on the Tooth Root Bending Stress Test of Hypoid Gear of the Driving Axle
حسب: Wang Kai, وآخرون
منشور في: (2017-01-01)

Tooth surface mismatch modification method of cycloidal bevel gear based on conjugate tooth surface modification
حسب: Jing DENG, وآخرون
منشور في: (2020-03-01)

Tooth surface mismatch design of cycloidal bevel gear based on two directions modification of pinion cutter
حسب: Shaowu NIE, وآخرون
منشور في: (2024-03-01)

GENERATION AND TOOTH CONTACT ANALYSIS (TCA) OF HYPOID GEAR DRIVE
حسب: Mohammad Q. Abdullah, وآخرون
منشور في: (2023-07-01)

Modification Design and Experimental Verification of Spiral Bevel Gear Tooth Surface Based on Quantitative Mismatch
حسب: Geng Longlong, وآخرون
منشور في: (2023-11-01)

Optimization of Churning Resistance of Hypoid Gear for Automobile Rear Axle
حسب: Yunxiao Shen, وآخرون
منشور في: (2021-09-01)

Research on gear micro-modification and vibration and noise reduction of electric drive axles
حسب: HUANG Junming, وآخرون
منشور في: (2025-10-01)

Tooth Contact Analysis and Adjustment Calculation of Real Tooth Surfaces of Hypoid Gears
حسب: Han Kunpeng, وآخرون
منشور في: (2023-04-01)

Research on Transmission Error of Hypoid Gear based on Real Tooth Surface
حسب: Yimin Mo, وآخرون
منشور في: (2022-01-01)

Study on Lapping Position Control of Real Tooth Surface of Hypoid Gear
حسب: Yang Jianjun, وآخرون
منشور في: (2018-01-01)

Tooth Contact Analysis and Experimental Verification of Oerlikon Cycloidal Hypoid Gear
حسب: Du Jinfu, وآخرون
منشور في: (2015-01-01)

Design of Gleason High-ratio Hypoid Gear with Parallel Tooth Depth
حسب: Wang Zhiyong, وآخرون
منشور في: (2018-01-01)

Design and Analysis for Hypoid Gears with Ease-Off Flank Modification
حسب: Qin Wang, وآخرون
منشور في: (2022-01-01)

Comparison of meshing characteristics and dynamic behavior of hypoid gear drive under different load conditions
حسب: Xiaole Wang, وآخرون
منشور في: (2024-12-01)

Design of high-reduction hypoid gears meshing in plane of action
حسب: Atsushi SUZUKI, وآخرون
منشور في: (2017-12-01)

Study on Strength Failure Mechanism of Super-reduction Ratio Hypoid Gears
حسب: Yu Zhang, وآخرون
منشور في: (2022-08-01)

Manufacturing Technology Status and Developmental Trend for Spiral Bevel Gear Used in Automotive Drive Axle
حسب: Deng Xiaozhong, وآخرون
منشور في: (2015-01-01)

A flank modification method for spiral bevel gears based on mismatch topography adjustment
حسب: Shaowu NIE, وآخرون
منشور في: (2018-06-01)

Research of the Lapping Burn and Inhibition of Hypoid Gear
حسب: Liu Xianghuan, وآخرون
منشور في: (2016-01-01)

Tooth Flank Mismatch Meshing Analysis for Spiral Bevel Gear Based on Tilt Cutting Method
حسب: Shaowu Nie, وآخرون
منشور في: (2019-09-01)

Research of the Influence of Tooth Profile Modification on the Tooth Surface Vibration Noise of Automobile Transmission Gear
حسب: Pan Haibo
منشور في: (2016-01-01)

Effect of Furnace Loading Method on Deformation Consistency of Constant-depth Tooth Hypoid Gear in Heat Treatment
حسب: Yimin Mo, وآخرون
منشور في: (2019-06-01)

Synchronous Modification Design for Bilateral Tooth Surface of Spiral Bevel Gear by Dual Duplex Spread Blade Method
حسب: Jianjun Yang, وآخرون
منشور في: (2019-07-01)

Gear Surface Design and Contact Analysis of Cycloid Bevel Gear based on Deviation Tooth Surface
حسب: Yang Jianjun, وآخرون
منشور في: (2018-01-01)

An Indirect Evaluation method for Running Stability of Hypoid Gears
حسب: 黄昌华, وآخرون
منشور في: (1999-01-01)

Design and Test of a Hypoid- cylindrical Gear Reducer
حسب: Wei Bingyang, وآخرون
منشور في: (2016-01-01)

Face Hobbing Method of Spiral Bevel and Hypoid Gears
حسب: 曾韬, وآخرون
منشور في: (1996-01-01)

A Numerical Gear Rolling Test Method for Face-Hobbed Hypoid Gears
حسب: Jinfu Du, وآخرون
منشور في: (2023-09-01)

Contact Simulation and Dynamic Performance Test of Ease-off Modified High Reduction Hypoid Gears
حسب: Gu Dewan, وآخرون
منشور في: (2023-05-01)

Influence of the Correction of Cycloid Tooth Bevel Gear Cutter Head Radius on the Tooth Surface Contact Performance
حسب: Han Zhengyang, وآخرون
منشور في: (2017-01-01)

Improvement of Calculating Method on Geometric Parameters of Epicycloid Hypoid Gear
حسب: Dong Xuezhu
منشور في: (1998-01-01)

Friction-Induced Efficiency Losses and Wear Evolution in Hypoid Gears
حسب: Eugeniu Grabovic, وآخرون
منشور في: (2022-08-01)

Research on Noise Reduction Modification Design of High Speed EMU Traction Arc Toothed Cylindrical Gears
حسب: Jianping Sun, وآخرون
منشور في: (2023-12-01)

Effects of tooth surface modification on planar double-enveloping hourglass worm gear drives
حسب: Fayang HE, وآخرون
منشور في: (2018-04-01)

Fundamental study on estimation of tooth contact area based on combined image from temperature monitor images of tooth surface with a high-speed-camera thermography and on meshing vibration for high reduction ratio hypoid gear with a three-tooth pinion
حسب: Masao NAKAGAWA, وآخرون
منشور في: (2024-11-01)

Research of Optimization of Grinding Parameter of Hypoid Gear based on Orthogonal Experiment
حسب: Mo Yimin, وآخرون
منشور في: (2019-01-01)

Modeling and Finite Element Analysis of Hypoid Gear Cutting by Completed Method
حسب: Lin Xi
منشور في: (2017-01-01)

Study on Heat Treatment Distortion of Hypoid Gear and Contact Zone Influence
حسب: Zhou Tingmei, وآخرون
منشور في: (2019-01-01)

Efficiency of Bevel and Hypoid Gears—Test Rig Development and Experimental Investigations
حسب: Lorenz Constien, وآخرون
منشور في: (2024-09-01)

Measurement of contact pattern displacement of hypoid gears with optical thermal camera
حسب: Stefan GERDHENRICHS, وآخرون
منشور في: (2024-09-01)