Cu-TiB metal matrix composites prepared by powder metallurgy route

Titanium boride (TiB) is characterized by good conductivity, high strength and high melting point. In this work, TiB was used to make Cu-TiB metal matrix composites (MMCs). Amounts of TiB added into Cu matrix were 2wt.%, 5wt.%, 10 wt.% and 15 wt.%. The samples were pressed at pressures of 5...

書誌詳細
出版年:	Science of Sintering
主要な著者:	Guo Z., Li N., Hu J.
フォーマット:	論文
言語:	英語
出版事項:	International Institute for the Science of Sintering, Beograd 2015-01-01
主題:	titanium boride Cu-TiB metal matrix composite powder metallurgy hardness conductivity
オンライン･アクセス:	http://www.doiserbia.nb.rs/img/doi/0350-820X/2015/0350-820X1502165G.pdf

類似資料

Effect of TiB content on the properties of Al-TiB composites
著者:: Yang Shen, 等
出版事項: (2018-01-01)

Solid state batteries (SSBs) prepared with powder metallurgy route
著者:: Hu J., 等
出版事項: (2013-01-01)

Synthesis of TiB2 powders by borothermal and carbothermal reduction of TiO2
著者:: Abdelgawad Mohamed Mahrous Hussein, 等
出版事項: (2024-06-01)

Investigations on microstructure and mechanical properties of Mg-5wt.% Cu-TiB2 composites produced via powder metallurgy route
著者:: Stalin B., 等
出版事項: (2020-01-01)

Microstructure and mechanical properties of in-situ TiB2/AlSi7Mg composite via powder metallurgy and hot extrusion
著者:: Cunguang Chen, 等
出版事項: (2022-07-01)

Ballistic performance of titanium-based layered composites made using blended elemental powder metallurgy and hot isostatic pressing
著者:: Pavlo Markovsky, 等
出版事項: (2024-09-01)

Cytotoxicity, Corrosion Resistance, and Wettability of Titanium and Ti-TiB<sub>2</sub> Composite Fabricated by Powder Metallurgy for Dental Implants
著者:: Ali Mohammad Ali Aljafery, 等
出版事項: (2024-05-01)

Microstructure and mechanical behaviour of Ti-Cu foams synthesized via powder metallurgy technique
著者:: Abhishek Sharma, 等
出版事項: (2021-01-01)

The effect of synthesis of the starting powders on the properties of Cu-Ti-TiB2 alloy obtained by laser melting
著者:: Stašić J., 等
出版事項: (2020-01-01)

EFFECT OF ZIRCONIUM ADDITION ON MICROSTRUCTURE AND PROPERTIES OF PURE TI PRODUCED BY POWDER METALLURGY
著者:: Hussein H. Kadhum, 等
出版事項: (2024-05-01)

Mechanical and electrical properties of graphene nanosheet reinforced copper matrix composites materials produced by powder metallurgy method
著者:: Albartouli Ahmed Basheer Mohammed, 等
出版事項: (2023-01-01)

Exploring powder metallurgy-processed Ti–25Ta-xCu alloys for potential biomedical applications
著者:: R. Suárez-Martínez, 等
出版事項: (2024-07-01)

Analysis of Cu-decorated Ti particles as a reinforcement for AZ91 alloys prepared using the powder metallurgy method
著者:: Yuhui Zhang, 等
出版事項: (2024-05-01)

Properties of aluminum matrix Nano composites prepared by powder metallurgy processing
著者:: Amal E. Nassar, 等
出版事項: (2017-07-01)

Advantages and effectiveness of the powder metallurgy in manufacturing technologies
著者:: A. Panda, 等
出版事項: (2018-01-01)

Microstructural analysis of sintered pure-titanium and titanium/hydroxyapatite (HA) surgical implant materials under different temperatures and HA doped conditions produced by powder metallurgy
著者:: Ebuzer Aygul, 等
出版事項: (2020-01-01)

Studying the Microstructure of Al-Ti Alloy Prepared by Powder Metallurgy using Three Different Percentages of Ti
著者:: Sahib Mohammed Mahdi, 等
出版事項: (2020-06-01)

Fatigue Improvement of Additive Manufactured Ti–TiB Material through Shot Peening
著者:: Liza-Anastasia DiCecco, 等
出版事項: (2021-09-01)

Optimization of Process Parameters of Aluminium 7075/TiCnp MMC Fabricated Using Powder Metallurgy Route
著者:: Ashok Raj Rajendran, 等
出版事項: (2024-02-01)

Development and characterisation of low-cost powder metallurgy Ti–Cu–Fe alloys
著者:: L. Bolzoni, 等
出版事項: (2023-05-01)

Effects of SiC Nanoparticles on the Properties of Titanium-Matrix Foams Processed by Powder Metallurgy
著者:: Ensieh Edalati, 等
出版事項: (2017-08-01)

Fabrication of TiB2 coatings by electrophoretic deposition of synthesized TiB2 nanoparticles in molten salts
著者:: Jun Zhang, 等
出版事項: (2022-05-01)

Evolution process of T1 precipitate in Al–Cu–Li–TiC/TiB2 alloy during aging treatment
著者:: Jiadong Li, 等
出版事項: (2024-11-01)

A well-balanced strength and electrical conductivity in rolled composite prepared by in-situ TiB2p/Cu composite powder
著者:: Hao Shi, 等
出版事項: (2023-11-01)

Formation and properties of TiB2-Ni composite ceramics
著者:: Vlasova Marina, 等
出版事項: (2016-01-01)

Effect of Molybdenum Content on Microstructure and Mechanical Properties of Ti-Mo-Fe Alloys by Powder Metallurgy
著者:: Hyo-Woon Hwang, 等
出版事項: (2022-07-01)

Effect of Cu–Al Ratio on Microstructure and Mechanical Properties of Cu–Al Alloys Prepared by Powder Metallurgy
著者:: Yuze Wang, 等
出版事項: (2024-08-01)

Effects of Mo equivalent on the phase constituent, microstructure and compressive mechanical properties of Ti–Nb–Mo–Ta alloys prepared by powder metallurgy
著者:: Huicong Li, 等
出版事項: (2022-01-01)

Effect of nano-TiC/TiB2 on recrystallization, texture and mechanical properties of Al–Cu–Li alloy during solid-solution treatment
著者:: Haiyao Wang, 等
出版事項: (2023-11-01)

Peculiarities of structure state and mechanical characteristics in ion-plasma condensates of quasibinary system borides W2B5-TiB2
著者:: Sobol O.V., 等
出版事項: (2006-01-01)

Laser Surface Modification in Ti-xNb-yMo Alloys Prepared by Powder Metallurgy
著者:: Inmaculada Tendero, 等
出版事項: (2021-02-01)

A Novel Process to Produce Ti Parts from Powder Metallurgy with Advanced Properties for Aeronautical Applications
著者:: Tamas Miko, 等
出版事項: (2023-03-01)

Development of Ti–In alloys by powder metallurgy for application as dental biomaterial
著者:: L. Romero-Resendiz, 等
出版事項: (2021-03-01)

Effect of Cu nanoparticles on microhardness and physical properties of aluminum matrix composite prepared by PM
著者:: Omar Hassan Mahmood, 等
出版事項: (2025-03-01)

Effect of TiB2 on the mechanical and tribological properties of marine grade Aluminum Alloy 5052: An experimental investigation
著者:: Sheikh Aamir Farooq, 等
出版事項: (2024-03-01)

Microhardness Distribution of Long Magnesium Block Processed through Powder Metallurgy
著者:: Jiaying Wang, 等
出版事項: (2022-12-01)

Effect of Mn on microstructure and properties of Cu-12Al powder metallurgy alloy
著者:: Guofei Zhang, 等
出版事項: (2020-01-01)

Preparation of in-situ TiB2 reinforced aluminum matrix composites assisted by two steps of ultrasonic vibration
著者:: Zhengcai Liu, 等
出版事項: (2021-01-01)

Laser Beam Welding of a Ti-15Mo/TiB Metal–Matrix Composite
著者:: Maxim Ozerov, 等
出版事項: (2021-03-01)

Microstructures and Mechanical Properties of Nanocrystalline AZ31 Magnesium Alloy Powders with Submicron TiB<sub>2</sub> Additions Prepared by Mechanical Milling
著者:: Haiping Zhou, 等
出版事項: (2020-06-01)