On the Fabrication of Metallic Single Crystal Turbine Blades with a Commentary on Repair via Additive Manufacturing

The turbine section of aircraft engines (both commercial and military) is an example of one of the most hostile environments as the components in this section typically operate at upwards of 1650 °C in the presence of corrosive and oxidative gases. The blades are at the heart of the turbine section...

وصف كامل

التفاصيل البيبلوغرافية
الحاوية / القاعدة:	Journal of Manufacturing and Materials Processing
المؤلفون الرئيسيون:	Nicole Marie Angel, Amrita Basak
التنسيق:	مقال
اللغة:	الإنجليزية
منشور في:	MDPI AG 2020-10-01
الموضوعات:	aircraft engines turbine blades single crystal investment casting repair additive manufacturing
الوصول للمادة أونلاين:	https://www.mdpi.com/2504-4494/4/4/101

مواد مشابهة

Design and Processing of Gas Turbine Blades Based on Additive Manufacturing Technology
حسب: Xuan Liu, وآخرون
منشور في: (2023-08-01)

Research progress in additive manufacturing for repair technology of single crystal superalloy turbine rotor blades for aero-engine
حسب: QIN Renyao, وآخرون
منشور في: (2024-12-01)

Technologies of Wind Turbine Blade Repair: Practical Comparison
حسب: Leon Mishnaevsky, وآخرون
منشور في: (2022-02-01)

General View of Rhenium-Rich Particles along Defect Grain Boundaries Formed in Nickel-Based Single-Crystal Superalloy Turbine Blades: Formation, Dissolution and Comparison with Other Phases
حسب: KeeHyun Park, وآخرون
منشور في: (2021-10-01)

Simulation and Experimental Study of Gas Turbine Blade Tenon-Root Detachment on Spin Test
حسب: Maoyu Yu, وآخرون
منشور في: (2024-08-01)

Multiscale modelling and simulation of single crystal superalloy turbine blade casting during directional solidification process
حسب: Xu Qingyan, وآخرون
منشور في: (2014-07-01)

A Robust Scheduling Framework for Re-Manufacturing Activities of Turbine Blades
حسب: Lei Liu, وآخرون
منشور في: (2022-03-01)

The Effect of Shell Thickness, Insulation and Casting Temperature on Defects Formation During Investment Casting of Ni-base Turbine Blades
حسب: Raza M., وآخرون
منشور في: (2015-12-01)

Manufacturing processes, life cycle analysis, and future challenges for wind turbine blades
حسب: Edgar Andres Olivera-Castillo, وآخرون
منشور في: (2022-10-01)

Numerical Study of a Novel Concept for Manufacturing Savonius Turbines with Twisted Blades
حسب: Victor Mendoza, وآخرون
منشور في: (2020-04-01)

Investigation on Designing and Development of a Selective Laser Melting Manufactured Gas Turbine Blade—Proof-of-Concept
حسب: Mihaela Raluca Condruz, وآخرون
منشور في: (2025-05-01)

High Cycle Fatigue Data Transferability of MAR-M 247 Superalloy from Separately Cast Specimens to Real Gas Turbine Blade
حسب: Miroslav Šmíd, وآخرون
منشور في: (2020-10-01)

Method of scanning thin surfaces in repairing gas turbine blades
حسب: D. I. Kotlyar, وآخرون
منشور في: (2023-12-01)

Experimental Investigation on Quasi-Freckle Phenomenon in Single-Crystal-Blade Castings of Superalloys
حسب: Dexin Ma, وآخرون
منشور في: (2024-10-01)

Single crystal casting of gas turbine blades using superior ceramic core
حسب: Eun-Hee Kim, وآخرون
منشور في: (2020-05-01)

Cure-induced residual stresses and viscoelastic effects in repaired wind turbine blades: Analytical-numerical investigation
حسب: Ayush Varshney, وآخرون
منشور في: (2024-10-01)

Results of conjugate modeling and analysis of the thermal state of a high-pressure turbine blade
حسب: V. N. Matveev, وآخرون
منشور في: (2023-05-01)

Turbine Blade Tip Repair by Laser Directed Energy Deposition Additive Manufacturing Using a Rene 142–MERL 72 Powder Blend
حسب: Mohsen K. Keshavarz, وآخرون
منشور في: (2021-03-01)

Structural repair of wind turbine blades: Computational model for the evaluation of the effect of adhesive properties
حسب: Lennart Mischnaewski III, وآخرون
منشور في: (2021-04-01)

Effect of process parameters on microstructure and properties of superalloy turbine guide castings by a novel electromagnetic oscillation method
حسب: Zong-sheng Xie, وآخرون
منشور في: (2024-11-01)

Research on Wind Turbine Blade Damage Fault Diagnosis Based on GH Bladed
حسب: Zhitai Xing, وآخرون
منشور في: (2023-05-01)

An Evaluation of Blade Repair Techniques and Applicability for Tidal Turbines
حسب: Ben Thomas, وآخرون
منشور في: (2025-09-01)

Study on the repair parameters for trailing‐edge bonding failure of wind turbine blade in service
حسب: Hui Li, وآخرون
منشور في: (2023-01-01)

Wind Turbine Blade Design
حسب: Richard J. Crossley, وآخرون
منشور في: (2012-09-01)

Development of a Laser Cladding Technology for Repairing First-Stage High-Pressure Turbine Blades in Gas Turbine Engines
حسب: Stepan Tukov, وآخرون
منشور في: (2025-08-01)

Stress Field Simulation of Single Crystal Turbine Blade During Unidirectional Solidification
حسب: LI Shifeng, وآخرون
منشور في: (2018-02-01)

The Concept of Segmented Wind Turbine Blades: A Review
حسب: Mathijs Peeters, وآخرون
منشور في: (2017-07-01)

Effect of Manufacturing Processes on Blade Throat Size and Position in a Steam Turbine Diaphragm
حسب: Petr Eret, وآخرون
منشور في: (2022-06-01)

Design and Experimental Study of Turbine Blade Cooling Structure for an Engine
حسب: Jintao Jiang, وآخرون
منشور في: (2025-09-01)

Automated Defect Detection and Decision-Support in Gas Turbine Blade Inspection
حسب: Jonas Aust, وآخرون
منشور في: (2021-01-01)

Influence of the blade size on the dynamic characteristic damage identification of wind turbine blades
حسب: Chen Peng, وآخرون
منشور في: (2023-04-01)

Prediction of fatigue life of geometrically deviated steam turbine blades under thermo-mechanical conditions
حسب: Makgwantsha Hermelton Mashiachidi, وآخرون
منشور في: (2024-01-01)

A real-time measuring technology for studying distortion of hydraulic turbine blade castings during heat treatment process
حسب: Yu Hailiang, وآخرون
منشور في: (2011-08-01)

Fatigue life prediction of mistuned steam turbine blades subjected to deviations in blade geometry
حسب: Makgwantsha Mashiachidi, وآخرون
منشور في: (2023-10-01)

Welding procedures of Turbine Blades by Using ER 309L Austenitic Filler Wire
حسب: A.H. Fadhil, وآخرون
منشور في: (2017-01-01)

Application of Rapid Prototyping Technology in the Manufacturing of Turbine Blade With Small Diameter Holes
حسب: Deja Mariusz, وآخرون
منشور في: (2018-05-01)

The Use of Coherence Functions of Acoustic Emission Signals as a Method for Diagnosing Wind Turbine Blades
حسب: Artur Bejger, وآخرون
منشور في: (2023-11-01)

Application of Modified Cores for Grain Refinement in Castings of Aircraft Turbine Blades
حسب: Binczyk F., وآخرون
منشور في: (2017-09-01)

ANALYSIS OF DAMAGED TURBINE BLADES OF THE ENGINE MPM 20
حسب: Jozef Čerňan, وآخرون
منشور في: (2016-06-01)

Structural Design, Analysis, and Testing of a 10 kW Fabric-Covered Wind Turbine Blade
حسب: Dong-Kuk Choi, وآخرون
منشور في: (2020-06-01)