Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing”
In the above article <xref ref-type="bibr" rid="ref1">[1]</xref>, Figure 3 should read “Isometric view of two wires forming a capacitor in the measured configuration. The yellow wire is the top plate and the red is the bottom plate of a capacitor. The gray...
| Main Authors: | , , , , , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
IEEE
2020-01-01
|
| Series: | IEEE Access |
| Online Access: | https://ieeexplore.ieee.org/document/9096628/ |
| id |
doaj-ec2017d558ef4bb3b1586ff30d12a214 |
|---|---|
| record_format |
Article |
| spelling |
doaj-ec2017d558ef4bb3b1586ff30d12a2142021-03-30T01:41:44ZengIEEEIEEE Access2169-35362020-01-018871848718410.1109/ACCESS.2020.29918969096628Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing”Carolyn Carradero Santiago0Christiaan Randall-Posey1Andrei-Alexandru Popa2Lars Duggen3Brian Vuksanovich4Pedro Cortes5Eric Macdonald6Department of Materials Science and Engineering, Youngstown State University, Youngstown, OH, USADepartment of Materials Science and Engineering, Youngstown State University, Youngstown, OH, USADepartment of Mechanical Engineering, Youngstown State University, Youngstown, OH, USADepartment of Mechanical Engineering, Youngstown State University, Youngstown, OH, USADepartment of Materials Science and Engineering, Youngstown State University, Youngstown, OH, USADepartment of Materials Science and Engineering, Youngstown State University, Youngstown, OH, USADepartment of Materials Science and Engineering, Youngstown State University, Youngstown, OH, USAIn the above article <xref ref-type="bibr" rid="ref1">[1]</xref>, Figure 3 should read “Isometric view of two wires forming a capacitor in the measured configuration. The yellow wire is the top plate and the red is the bottom plate of a capacitor. The gray is a dielectric elastomer lattice, the deformation of which can be indirectly determined by measuring the capacitance.” Figure 4 should read “Isometric (A) and bottom view (B) of a lattice with an alternative configuration in four quadrants for selective sensing. The selectivity can be extended to any combination of cells in both vertical and horizontal configurations.” In <xref ref-type="fig" rid="fig9">Figure 9</xref>, the <inline-formula> <tex-math notation="LaTeX">${x}$ </tex-math></inline-formula>-axis should read “Min Deformation Slow; Min Deformation Fast; Max Deformation Slow; Max Deformation Fast.” A sentence in the introduction should read “Within the context of additive manufacturing, lattices are the focus of significant research since they...” The authors requested this correction for clarity purposes.https://ieeexplore.ieee.org/document/9096628/ |
| collection |
DOAJ |
| language |
English |
| format |
Article |
| sources |
DOAJ |
| author |
Carolyn Carradero Santiago Christiaan Randall-Posey Andrei-Alexandru Popa Lars Duggen Brian Vuksanovich Pedro Cortes Eric Macdonald |
| spellingShingle |
Carolyn Carradero Santiago Christiaan Randall-Posey Andrei-Alexandru Popa Lars Duggen Brian Vuksanovich Pedro Cortes Eric Macdonald Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing” IEEE Access |
| author_facet |
Carolyn Carradero Santiago Christiaan Randall-Posey Andrei-Alexandru Popa Lars Duggen Brian Vuksanovich Pedro Cortes Eric Macdonald |
| author_sort |
Carolyn Carradero Santiago |
| title |
Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing” |
| title_short |
Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing” |
| title_full |
Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing” |
| title_fullStr |
Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing” |
| title_full_unstemmed |
Corrections to “3D Printed Elastomeric Lattices With Embedded Deformation Sensing” |
| title_sort |
corrections to “3d printed elastomeric lattices with embedded deformation sensing” |
| publisher |
IEEE |
| series |
IEEE Access |
| issn |
2169-3536 |
| publishDate |
2020-01-01 |
| description |
In the above article <xref ref-type="bibr" rid="ref1">[1]</xref>, Figure 3 should read “Isometric view of two wires forming a capacitor in the measured configuration. The yellow wire is the top plate and the red is the bottom plate of a capacitor. The gray is a dielectric elastomer lattice, the deformation of which can be indirectly determined by measuring the capacitance.” Figure 4 should read “Isometric (A) and bottom view (B) of a lattice with an alternative configuration in four quadrants for selective sensing. The selectivity can be extended to any combination of cells in both vertical and horizontal configurations.” In <xref ref-type="fig" rid="fig9">Figure 9</xref>, the <inline-formula> <tex-math notation="LaTeX">${x}$ </tex-math></inline-formula>-axis should read “Min Deformation Slow; Min Deformation Fast; Max Deformation Slow; Max Deformation Fast.” A sentence in the introduction should read “Within the context of additive manufacturing, lattices are the focus of significant research since they...” The authors requested this correction for clarity purposes. |
| url |
https://ieeexplore.ieee.org/document/9096628/ |
| work_keys_str_mv |
AT carolyncarraderosantiago correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d AT christiaanrandallposey correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d AT andreialexandrupopa correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d AT larsduggen correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d AT brianvuksanovich correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d AT pedrocortes correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d AT ericmacdonald correctionstox201c3dprintedelastomericlatticeswithembeddeddeformationsensingx201d |
| _version_ |
1724186609147969536 |