Optimization of Cutting Parameters of the Haynes 718 Nickel Alloy With Gas CO2 Laser

by Jana PETRŮ, Martin GREPL
Published 2011-06-01

Laser Cutting of Materials of Various Thicknesses

by Martin Grepl, Marek Pagáč, Jana Petrů
Published 2012-01-01

Laser Beam Drilling of Inconel 718 and Its Effect on Mechanical Properties Determined by Static Uniaxial Tensile Testing at Room and Elevated Temperatures

by Jana Petrů, Marek Pagáč, Martin Grepl
Published 2021-06-01

Porosity Analysis of Additive Manufactured Parts Using CAQ Technology

by Peter Pokorný, Štefan Václav, Jana Petru, Michaela Kritikos
Published 2021-02-01

Effect of the Cutting Tool Geometry on the Tool Wear Resistance When Machining Inconel 625

by Tomáš Zlámal, Jiří Hajnyš, Jana Petrů, Ivan Mrkvica
Published 2017-12-01

SURFACE MICROHARDENING STUDIES ON STEELS AFTER HIGH FEED MILLING

by Jana Petrů, Tomáš Zlámal, František Špalek, Robert Čep
Published 2018-06-01

Effect of the Cutting Tool Geometry on the Tool Wear Resistance when Machining Inconel 625

by Tomáš Zlámal, Jiří Hajnyš, Jana Petrů, Ivan Mrkvica
Published 2018-03-01

On modelling of simulation model for racing car frame torsional stiffness analysis

by David Krzikalla, Aleš Slíva, Jakub Měsíček, Jana Petrů
Published 2020-12-01

Hot Deformation Treatment of Grain-Modified Mg–Li Alloy

by Mariusz Król, Przemysław Snopiński, Marek Pagáč, Jiří Hajnyš, Jana Petrů
Published 2020-10-01

Influence of Scanning Strategy Parameters on Residual Stress in the SLM Process According to the Bridge Curvature Method for AISI 316L Stainless Steel

by Jiri Hajnys, Marek Pagáč, Jakub Měsíček, Jana Petru, Mariusz Król
Published 2020-04-01

A CHOICE OF THE OPTIMUM CUTTING RANGES FOR CUTTING NOZZLES A-SD FOR SELECTION OF METALLURGICAL MATERIAL

by Dana Stančeková, Anna Rudawska, Albert Kulla, Jana Petrů, Jozef Holubják
Published 2018-09-01

IMPACT OF CUTTING TOOL GEOMETRY ON THE DYNAMIC LOAD OF SYSTEM IN THE MACHINING PROCESS OF NICKEL ALLOY 625

by Jiří Hajnyš, Tomáš Zlámal, Jana Petrů, Marek Pagáč, Anna Rudawska
Published 2016-12-01

The Properties of Regenerative Polymer Mass

by Anna Rudawska, Albert Wierzchowski, Miroslav Müller, Jana Petrů, Nataša Náprstková
Published 2017-09-01

The effect of feed rate on durability and wear of exchangeable cutting inserts during cutting Ni-625

by Jana Petrů, Tomáš Zlámal, Robert Čep, Dana Stančeková, Marek Sadílek
Published 2017-01-01

MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING OF SPECIAL ALLOYS

by Tomáš Zlámal, Jana Petrů, Ondřej Vortel, Marek Pagáč, Pavel Krajkovič
Published 2016-09-01

EFFECT OF CHIP BREAKERS ON THE CUTTING FORCE DURING THE MACHINING OF STEEL C45

by Jiří Kratochvíl, Jana Petrů, Marek Pagáč, Jozef Holubják, Jozef Mrazik
Published 2017-03-01

Effect of Periodic Water Clusters on AISI 304 Welded Surfaces

by Madhulika Srivastava, Akash Nag, Lucie Krejčí, Jana Petrů, Somnath Chattopadhyaya, Sergej Hloch
Published 2021-01-01

Experimental Investigation of Cutting Forces in High-Feed Milling of Titanium Alloy

by Jana Petrů, Lukáš Drábek, Jiří Hajnyš, Dalibor Jurok, Marek Pagáč, Jakub Měsíček
Published 2020-03-01

Complex Corrosion Properties of AISI 316L Steel Prepared by 3D Printing Technology for Possible Implant Applications

by Josef Hlinka, Martin Kraus, Jiri Hajnys, Marek Pagac, Jana Petrů, Zbigniew Brytan, Tomasz Tański
Published 2020-03-01

On Aluminum Honeycomb Impact Attenuator Designs for Formula Student Competitions

by Phu Ma Quoc, David Krzikalla, Jakub Mesicek, Jana Petru, Jakub Smiraus, Ales Sliva, Zdenek Poruba
Published 2020-10-01